PolarStar

POLARSTAR Foster QD Male 1/8" NPT FEMThis Foster 23-2 QD fitting is used as part of the QD fitting assembly provided with all PolarStar Air Rigs.

∙ Requires 6mm x 1/8PTC fitting (part# 10000292) to make complete assembly.

POLARSTAR Male Quick Disconnect (QD) Fitting Assembly∙ High quality, precision crafted HPA component
∙ ​Compatible with standard HPA as well as SLP tanks

Titan Power Li-on HPA V2 - 350mAh 7.4v JSTUnder Discharge, Over Charge, and Short Protection
Titan Power HPA batteries are protected from active-drawing HPA systems such as Polarstar and Wolverine, and will never allow itself to…

POLARSTAR Braided Air Line ™ (42" Black)Highly flexible rubber air line reinforced with a nylon braided sheath promotes maximum mobility while reducing the risk of kinking.

∙ Fitted with standard QD couplings
∙ Lightweight…

VB POWER Lipo 7.4V 300mAh 35C/70C for Polarstar FCU (HPA)∙ Voltage: 7.4 Volt (2 Cells)
∙ Capacity: 300 mAh / 35 C
∙ Charging current (max.): 0.3 A
∙ Discharge current (max.): 10.5 A
∙ Watthour: 2.2 Wh

POLARSTAR TechT Gun Sav Maintenance GreaseGun Sav is specially blended for minimal "stiction", and maximum part movement. Gun Sav adheres to the part, and stays where you put it. Ideal for use on Polarstar Fusion Engine o-rings…

POLARSTAR Wire Harness Rev. 2 - Lenght 7,5" 19cmNew quality electric wire with RCY connectors ideal replace to your damaged original wire suitable for FUSION ENGINE or JACK devices dedicated custom version for AMOEBA rifle…

POLARSTAR Bullet Valve Lead for 214 and 309 SolenoidsOkay, we've all done it. You just finish putting together the gearbox and can't quite figure out what is preventing the shell from closing all of the way. Yep, you just pinched…

POLARSTAR F2™ Nozzle∙ Drop in nozzle for PolarStar F2 HPA engines
∙ Machined aluminum construction
∙ Anodized finish
∙ Material: Aluminum
∙ Manufacturer: PolarStar

∙ Compatibility: Polarstar F2 HPA Engines Used in…

POLARSTAR Wire Harness MCU. (3 pin JST/ A&K Connector. 18" 45cmThe MCU wire harness is intended for use with REV3 FCU's that feature the built in MCU (Motor Control Unit) for running the replica's box magazine. This model features…

POLARSTAR Switchboard V2This switchboard is designed to replace the original trolley type trigger switch in a traditional TM spec V2 gearbox. It is not compatible with variants of the V2 gearbox which use a snap-action/microswitch…

POLARSTAR Wire Harness Rev. 2 - Lenght 18" 45cmNew quality electric wire with RCY connectors ideal replace to your damaged original wire suitable for FUSION ENGINE or JACK devices dedicated custom version for AMOEBA rifle…

POLARSTAR Complete Seal Set, MR - Micro RegulatorSet includes:∙ 2x M1.5 x 4.5 (Buna 70) - Body ID
∙ 1x M2.0 x 14.0 (Buna 70) - Piston OD
∙ 1x Base Seal
∙ (Covers GEN1 and GEN2)

PPOLARSTAR Replacement gauge for PolarStar MRS as well as GEN1 and GEN2 Micro Regs∙ 0-220psi operating range.
∙ 25mm dial.
∙ 1/8 NPT thread.
∙ High quality, precision crafted HPA component

POLARSTAR Trigger Lead. 6" Universal. (2 pin JST/ Bare Lead)The trigger lead is mainly used for soldering into the existing trigger switch of an AEG gearbox such as on VFC HK417 or Classic Army KAC LMG.

∙ 6" length
∙ 2pin JST…

POLARSTAR Universal Plugboard. Includes Heat ShrinkThe Universal Plugboard is used in all of our MG series kits such as the M249 and is used across all of our systems including the Fusion Engine. It is also useful for custom…

POLARSTAR Micro Regulator - “Micro Reg”, GEN2 (Regulator Only - Black)When the original Micro Regulator™ came out it was an instant hit since it was ultra compact yet offered the performance of regulators twice its size.…

POLARSTAR Fusion Engine™ Nozzle M249Features∙ Drop in nozzle for PolarStar F2 HPA engines
∙ Machined aluminum construction
∙ Anodized finish
∙ Compatibility: Polarstar F2™ HPA Nozzle M249
∙ Material: Aluminum
∙…

POLARSTAR Fusion Engine™ Nozzle M4/M16The air nozzles for the Fusion Engine come in up to 6 different colors which identify how much the nozzle restricts air flow out of the engine. This starts at the Green nozzle which has the…

Kythera™ SA Nozzles Nozzle ∙ Drop in nozzle for PolarStar Kythera™ HPA engines
∙ Machined aluminum construction
∙ Anodized finish
∙ Material: Aluminum
∙ Manufacturer: PolarStar
∙ Compatibility: Polarstar Kythera™…

Updated for an Off-Center World

The offset version of the F2™ is the first true closed bolt offset HPA conversion kit on the market and, although it took a while to develop, we are pleased to say it is worth the wait. The F2™…

POLARSTAR F2™ HPA Conversion Kit - V2 M4/M16Attention: QD Fitting not included and Sold Separately

The F2™ incorporates a new one-piece, lightweight poppet valve design yet still operates on the same principle as the Fusion…

POLARSTAR Kythera SA™ Conversion Kit, Semi-Auto, V3, AK 6Features∙ Designed from the ground up as a high performance mechanical HPA system, not a modification of a solenoid operated design
∙ Patent pending valve mechanism…

POLARSTAR Kythera SA. Conversion Kit (Single Shot) Semi Only. V2/ M4, M16Features∙ Designed from the ground up as a high performance mechanical HPA system, not a modification of a solenoid operated design
∙ Patent pending…

POLARSTAR MICRO-REG-KIT-36 / MR - Micro Regulator Air System - “Micro REG”, GEN2 with Airline 36"When the original Micro Regulator™ came out it was an instant hit since it was ultra compact yet offered the performance of…

POLARSTAR MRS-RIG-KIT-36 / MRS "Modular Regulator Air System" Air Rig with Airline 36"POLARSTAR MRS "Modular Regulator System" Air RigIntroducing the new Modular Regulator System (MRS) designed and manufactured by PolarStar…

POLARSTAR F2™ Conversion Kit for VFC HK417/G28Attention: QD Fitting not included and Sold Separately

The F2™ incorporates a new one-piece, lightweight poppet valve design yet still operates on the same principle as the Fusion…